This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Bug Report Archive / Re: E60->E6x cause jump position to the next pattern

« on: August 24, 2010, 12:02:03 »

...
I added "D00" at the end of the same row where E60 was sets (*).
...

Sorry, must be :
''I added "D00" at the end of the same column where E60 was sets (*).''

About your picture :
It works fine, adding "D00" at the bottom of the same column where the "E60->E6x" effect sets. In fact, wherever the column I put the "D00" it works now.

2

Bug Report Archive / Re: E60->E6x cause jump position to the next pattern

« on: August 23, 2010, 04:04:38 »

I see what you mean.
I added "D00" at the end of the same row where E60 was sets (*).
I had no "E6x" ended at the bottom, so not a problem of left or right.

I did it again to be sure, and now it works
(*) Well, not so sure now...

Ok, that's the trick !

Thanks for that.

3

Bug Report Archive / Re: E60->E6x cause jump position to the next pattern

« on: August 22, 2010, 22:40:59 »

That's could have been a nice trick, but...

In my first pattern, it works fine going to the next. But in this second pattern, it doesn't works with the third one. A bad jump is back again... 

Thanks anyway.

4

MilkyTracker Bug Reports / Crash while loading a sample

« on: August 22, 2010, 22:24:37 »

Hello,

MT crashed during loading a 31st sample.

Here's the Mac report :
-------------------------

...

Exception Type:  EXC_BAD_ACCESS (SIGSEGV)
Exception Codes: KERN_INVALID_ADDRESS at 0x000000006c61626f
Crashed Thread:  13

...

Thread 13 Crashed:
0                                 0x6c61626f 0 + 1818321519
1   libSystem.B.dylib                0x989501e3 _pthread_tsd_cleanup + 88
2   libSystem.B.dylib                0x9894fdf6 _pthread_exit + 154
3   libSystem.B.dylib                0x989476a2 thread_start + 34

...

Thread 13 crashed with X86 Thread State (32-bit):
  eax: 0x6c61626f  ebx: 0x9638613b  ecx: 0x00000001  edx: 0x9638613b
  edi: 0x0000011b  esi: 0x746e6569  ebp: 0xb07c1ef8  esp: 0xb07c1edc
   ss: 0x0000001f  efl: 0x00010206  eip: 0x6c61626f   cs: 0x00000017
   ds: 0x0000001f   es: 0x0000001f   fs: 0x0000001f   gs: 0x00000037
  cr2: 0x6c61626f

-------------------------

I tryed to load it alone in a new song, it works fine.
I tryed to load it alone at the 31st position, works fine also.


Milkytracker v0.90.85
Mac OS X v10.6.4 (Snow Leopard)

5

Bug Report Archive / E60->E6x cause jump position to the next pattern

« on: August 22, 2010, 22:14:40 »

Hello,

I used E60-E62 in one pattern. During playong the song, everything goes fine.
Then, the next pattern is played but passing the top of this pattern and starting at the same row where the E60 effect was set on the previous pattern.
Seems the jump position is not cleared after the last loop.

Milkytracker v0.90.85
Mac OS X v10.6.4 (Snow Leopard)